SP Flash Tool v5 vs v6 is not a choice between an old and a new version. They are two branches of MediaTek’s SmartPhone Flash Tool that are updated side by side. v5 loads a scatter file (MTxxxx_Android_scatter.txt), and v6 loads a flash.xml file. The firmware for your phone decides which one you need, not the version number.

SP Flash Tool v5 vs v6 at a Glance

Item SP Flash Tool v5 SP Flash Tool v6
Firmware file it loads MTxxxx_Android_scatter.txt flash.xml (often in a download_agent folder)
Field you load it in Scatter-loading File Download-XML
Download Agent protocol XFlash (V5) XML (V6)
Typical phones Most MediaTek phones released between 2016 and about 2022 Newer MediaTek phones, mainly Dimensity and some newer Helio chips
Reads the other format? No No
Platforms Windows, Linux Windows, Linux
Still updated? Yes Yes

A UMIDIGI community administrator put it simply in July 2024: v6 “is just a different tool, not newer”, and both the v5 and v6 releases get frequent updates. Download sites list matching build numbers for both branches, for example 5.2404 and 6.2404.

Why There Are Two Versions

The Download Agent is the real difference

SP Flash Tool does not write to the phone by itself. It first sends a small program called the Download Agent (DA) to the phone through the BootROM or preloader. The DA then reads and writes the phone’s storage. MediaTek’s DA has used three protocols over the years:

  • Legacy, labelled V3, on older chips.
  • XFlash (V5), found on most MediaTek devices released between 2016 and about 2022. SP Flash Tool v5 uses it.
  • XML (V6), built on XFlash but with a new communication layer in which each command is an XML string. It is mainly found on Dimensity and some newer Helio chips. SP Flash Tool v6 uses it.

Because the phone side changed, the PC side changed too. That is why v6 asks for a different firmware description file and why a v5 package cannot simply be loaded into v6.

SP Flash Tool v5

v5 is the branch most guides and older firmware packages are written for. You load the scatter file in the Download tab and choose one of three modes: Download Only, Firmware Upgrade or Format All + Download. It also has a Readback function that technicians use to back up partitions. This site has several v5 builds, including SP Flash Tool v5.1820 and SmartPhone Flash Tool v5.1916.

SP Flash Tool v6

v6 was already in use by 2021, when a Hovatek forum user reported that it asked for flash.xml instead of a scatter file. You load flash.xml in the Download-XML field. Phones with secure boot may also need an authentication file, just as they do with v5. Our SP Flash Tool v6 guide walks through the full v6 flashing steps.

Which Version Does Your Phone Need?

  1. Get official firmware for your exact model and variant from the phone maker or an authorized source.
  2. Extract it and open the folder.
  3. If you see a file named like MT6765_Android_scatter.txt, use v5.
  4. If you see flash.xml, usually inside a download_agent folder, use v6.

Do not decide by the phone’s age or chip name alone. UMIDIGI told a BISON GT2 PRO 5G owner in 2024 that no Download-XML exists for that model and that v5 with the scatter file is the right tool. Also, you cannot convert one format into the other. When a user asked Hovatek in 2021 whether v5 firmware could be made v6-compatible, the answer was “No, at least not yet”. We have found no official converter since.

Requirements for Both Versions

  • A Windows or Linux PC. Neither branch has a mainstream macOS build.
  • The MediaTek USB VCOM driver. Use our MTK USB Driver 32bit & 64bit post, or the MTK driver ZIP linked on Google’s OEM USB drivers page.
  • Official firmware for your exact model, with the DA from the same package. Hovatek notes that some DA files only work with a specific MediaTek tool.
  • An authentication (.auth) file only if your firmware or the phone maker supplies one.
  • A backup of your data and a well-charged battery. Flashing official firmware usually erases the phone.

Where to get the tool: MediaTek has no public download page. Its Genio documentation says SP Flash Tool is available from the Genio Developer Center, which requires a non-disclosure agreement with MediaTek. Use the build that came with your firmware, or get it from our SP Flash Tools for all MTK devices page.

How to Use Each Version (Short Version)

Flashing with v5 (scatter firmware)

  1. Extract the tool and the firmware to separate folders with short paths.
  2. Run flash_tool.exe and open the Download tab.
  3. Load the scatter file in Scatter-loading File. The partition list fills in.
  4. Keep Download Only selected and click Download.
  5. Connect the switched-off phone. Wait for the green Download OK message, then unplug the phone and switch it on.

Flashing with v6 (flash.xml firmware)

  1. Run v6 and load flash.xml in the Download-XML field.
  2. Add an auth file only if your firmware includes one for your model.
  3. Choose Download Only, click Download, then connect the switched-off phone.

The full v6 steps, including when to untick the preloader, are in our v6 how-to guide.

Warning for both versions: avoid Format All + Download unless a technician tells you to use it. Formatting can erase calibration and identity data, and it can trigger authentication requests later.

Common Errors When Mixing v5 and v6

The file will not load (wrong format)

Loading a scatter file into v6, or flash.xml into v5, gives a format mismatch error. Switch to the branch that matches your firmware.

“lib DA not match” or other DA errors

Some DA files only work with a specific MediaTek tool. Use the DA that came with your firmware package and a tool build of the matching branch. Do not try random DA files.

The tool asks for an authentication file

This is not a v5 or v6 problem. Many newer MediaTek phones use Download Agent Authentication (DAA), which checks the DA’s signature against a key stored in the phone. The check happens on the phone, so switching between v5 and v6 does not get around it. If your firmware has no auth file, take the phone to an authorized service centre.

You cannot make a v6 backup

In 2021 Hovatek said that backing up a working phone’s firmware for later use with v6 was “Not possible at this time”. On v6 phones, keep a copy of the official firmware package instead of relying on a readback.

Other error codes

For BROM and DA error numbers, see our MTK SP Flash Tools error guide.

Related Guides

FAQ

Is SP Flash Tool v6 better than v5?

No. It is a separate branch for flash.xml firmware and the XML Download Agent. For scatter firmware, v5 is the correct tool, and both branches still receive updates.

Can SP Flash Tool v6 flash a scatter file?

No. v6 reads flash.xml only. If your firmware has MTxxxx_Android_scatter.txt, use v5.

My phone has a Dimensity chip. Do I need v6?

Probably, because the XML protocol is mainly found on Dimensity chips. Still, check the firmware folder first: the presence of flash.xml or a scatter file is the only reliable test.

Does either version work on a Mac?

No. Both branches are built for Windows and Linux only.

Which build number should I download?

MediaTek publishes no public changelog, so there is no official “latest” build. Use the build that came with your firmware or that your phone maker recommends, from the matching branch.

https://droid-developers.com/wp-content/uploads/2026/11/sp-flash-tool-v5-vs-v6-featured-1024x538.jpghttps://droid-developers.com/wp-content/uploads/2026/11/sp-flash-tool-v5-vs-v6-featured-150x150.jpgFahim MahmudFirmwareFlash ToolsHelp & TroubleshootingSP Flash Tool v5 vs v6 is not a choice between an old and a new version. They are two branches of MediaTek's SmartPhone Flash Tool that are updated side by side. v5 loads a scatter file (MTxxxx_Android_scatter.txt), and v6 loads a flash.xml file. The firmware for your phone...Android Help,Troubleshooting  & Stock Rom