SPD Flash Tool (Unisoc Upgrade Tool): How to Flash .pac Firmware
The SPD flash tool is the family of Windows programs (Upgrade Download, Research Download and Factory Download) that install .pac firmware on phones and tablets with a Unisoc chip, the brand formerly called Spreadtrum or “SPD”. You load the .pac file, click Start Downloading, then connect the switched-off phone while holding a volume key. This guide covers the requirements, every step, the error messages people meet most, and when to stop.
What the SPD Flash Tool Is
Unisoc started as Spreadtrum Communications. In 2018 Spreadtrum and RDA Microelectronics were combined under the UNISOC brand, which is why technicians still call these chips and tools “SPD”. Unisoc phone chips include the SC9863A and the T606, T616 and T700 series.
The flash tool comes in three versions. All of them load a .pac file and use essentially the same steps:
| Tool | Program file | Typical use |
|---|---|---|
| Upgrade Download (“SPD Upgrade Tool”) | UpgradeDownload.exe | Installing a full .pac firmware |
| Research Download | ResearchDownload.exe | Installing firmware; technicians also use it to read (back up) firmware |
| Factory Download | FactoryDownload.exe | Same flashing steps; sometimes works when the other two report an error |
These tools only work with Unisoc/Spreadtrum chips. For MediaTek phones use SP Flash Tool instead.
What is inside a .pac file
A .pac file is one package that holds the whole firmware: two small download loaders called FDL1 and FDL2, plus the partition images. The tool sends FDL1 to the phone’s download mode first. FDL1 starts the phone’s RAM and loads FDL2, which then writes the images to storage. This is why FDL1 and FDL2 must always stay selected.
Requirements
- A Windows PC and a good USB data cable. Use a USB 2.0 port if your PC has one, and unplug other Android devices.
- The Unisoc/SPD USB driver. Get it from our SPD SCI Android USB Driver post. In download mode the phone appears in Device Manager as SPRD U2S Diag (USB ID 1782:4D00). If the tool says your driver version “is too low”, install a newer driver.
- The flash tool. We could not find a public download page for these tools on Unisoc’s website. Our SPD Flash Tools R4.0.0001 post has ResearchDownload. A newer tool version can load .pac files that an old one rejects.
- Microsoft Visual C++ runtimes. Without them the tool may fail to start. Install the 2005, 2008 and 2010 packages (both x86 and x64 on a 64-bit PC) from Microsoft’s Visual C++ Redistributable downloads page.
- Official .pac firmware for your exact model and build or variant, from the phone maker or its service centre. A .pac for another model can brick the phone.
- A charged battery and a backup of anything you can still copy. A full .pac flash normally erases your personal data.
How to Flash .pac Firmware with the SPD Upgrade Tool
- Install the SPD driver, then extract the tool to a folder on your PC.
- Right-click UpgradeDownload.exe (or ResearchDownload.exe) and choose Run as administrator. If Windows SmartScreen shows a warning, choose More info and then Run anyway.
- Click the first icon at the top left, Load Packet. Select your .pac file and click Open. Wait while the tool unpacks it; the file name then appears at the top of the window.
- Optional: click the Settings icon to see the list of partitions. Leave everything ticked for a full flash. If you untick anything, FDL1 and FDL2 must stay ticked. Click OK.
- Click the third icon, Start Downloading. The status column shows Waiting….
- Switch the phone off completely. If it has a removable battery, leave the battery in.
- Hold the boot key, usually Volume Down (Volume Up on some models), and connect the USB cable. Keep holding the key until the progress bar is clearly moving. Without the key, the phone only starts charging.
- Wait. The phone’s screen stays blank during flashing. Do not move the cable or close the tool. Interrupting the flash can brick the phone.
- When the status shows Passed, click Stop Downloading, unplug the phone and switch it on.
Common Errors and Fixes
| Message | What it means | What to do |
|---|---|---|
| Stuck at “Waiting….” | The tool cannot find the phone | Charge the phone, check the driver, try another cable, port or PC, and hold the volume key while connecting |
| Phone only charges | The SPD driver is not attached to the phone | Install the SPD driver from Device Manager with Have Disk, then try again |
| “Bin packet version is not support! Load bin packet failed!” | The tool is too old or the .pac file is badly built | Use a newer tool version and a valid .pac from the maker |
| “Downloading failed : wait input time out” | The flash took too long and timed out | Use a newer tool version (R2.9.9008 or later), then flash again |
| “Failed: User cancel” | The volume key was pressed or released at the wrong moment | Hold the key while connecting and keep holding it until flashing is under way |
| “Failed incompatible partition” | The partition layout in the .pac does not match the phone | Try a newer tool version first. The Repartition option (Settings > Options) rewrites the partition table, so use it only with firmware made for your exact model |
| “Failed to create empty document” (CDLFWDriver Startup Fail) | Visual C++ runtimes are missing | Install the Visual C++ 2005, 2008 and 2010 packages |
| “Checking Bautrate” stays on screen | The tool failed while starting the flash | Disconnect, reseat the battery if it is removable, restart the tool and try again |
Errors about NV data or calibration
Messages such as “NV data in device is crashed” or “GSM Cali in phone is not calibrated” mean the tool cannot read the phone’s NV (radio calibration) data. This data controls the phone’s mobile network. Do not experiment with NV options or files from other phones. Stop and take the phone to the maker’s service centre.
The phone starts but loops or freezes
Make sure the .pac matched your exact model and build, then do a factory reset from recovery mode. Our boot loop fixes cover the next steps.
When to Use a Service Centre
- The phone shows no sign of life and never appears in Device Manager, even with a charged battery and a known-good cable.
- You cannot get official firmware for your exact model.
- The tool reports NV, calibration or partition errors that a newer tool version does not fix.
Related Guides
- SPD SCI Android USB Driver
- Download SPD Flash Tools R4.0.0001
- Android USB Driver for Windows 11 (All Major Brands)
- Phone Stuck in a Boot Loop? Universal Fixes for Android Phones
- SP Flash Tool v6: How to Use the New Version with flash.xml
FAQ
What is the difference between Upgrade Download and Research Download?
For flashing a .pac file there is almost none: both use the same steps. Research Download is also used to read firmware from a phone. If one tool will not load your .pac or reports an error, try the other one or Factory Download.
Does the SPD flash tool erase my data?
A full .pac flash normally replaces everything on the phone, including your apps, photos and settings. Back up first.
Why does the phone screen stay black while flashing?
That is normal. The phone is in download mode, and all progress is shown in the tool on the PC.
Can I flash a .pac file from a similar model?
No. The FDL loaders and partition layout are made for one model, and using another model’s loaders can, in theory, even damage the hardware. Use only the .pac for your exact model and build.
https://droid-developers.com/spd-flash-tool-unisoc-pac/https://droid-developers.com/wp-content/uploads/2026/11/spd-flash-tool-unisoc-pac-featured-1024x538.jpghttps://droid-developers.com/wp-content/uploads/2026/11/spd-flash-tool-unisoc-pac-featured-150x150.jpgFirmwareFlash ToolsHow ToThe SPD flash tool is the family of Windows programs (Upgrade Download, Research Download and Factory Download) that install .pac firmware on phones and tablets with a Unisoc chip, the brand formerly called Spreadtrum or 'SPD'. You load the .pac file, click Start Downloading, then connect the switched-off phone...Fahim MahmudFahim Mahmud[email protected]AdministratorDroid-Developers
Leave a Reply