There is no single Infinix firmware flash tool: the right tool depends on the chip inside your phone. Infinix phones with MediaTek chips are flashed with SP Flash Tool and a scatter file, while models with Unisoc chips use the Upgrade Download or Research Download tool with a .pac file. This guide shows how to tell which one your phone needs, how to flash it safely, and what to do when the tool gives an error.

Try the Official Infinix Update First

Flashing is a repair method, not the normal way to update. Infinix sends XOS updates over the air (OTA). On recent XOS versions the update check is under Settings > System > System Update. The menu name can differ between XOS versions, so if you do not see it, type “update” in the Settings search bar.

XOS 16, which is based on Android 16, is reaching existing Infinix phones in stages during 2026. If your model has not received it yet, wait for the OTA for your region. Flashing firmware meant for another region or variant to get an update early is a common way to lose network or brick a phone.

If the phone is still under warranty, or you are not comfortable flashing, take it to Carlcare. Carlcare is the official after-sales service for Infinix, TECNO and itel phones, and you can find the nearest centre or check your warranty on the Carlcare website.

Which Flash Tool Does Your Infinix Phone Need?

Chipset Firmware format Flash tool PC driver
MediaTek (Helio, Dimensity) Scatter file (MTxxxx_Android_scatter.txt) or flash.xml SP Flash Tool (v5 for scatter, v6 for flash.xml) MediaTek Preloader USB VCOM or BROM driver
Unisoc (formerly Spreadtrum) .pac file Upgrade Download, Research Download or Factory Download Spreadtrum SCI USB driver

Unisoc is the current name of Spreadtrum; the two brands were combined under the Unisoc name in 2018. That is why Unisoc phones still use “SPD” or “Spreadtrum” tools and drivers.

Examples of Current Infinix Models

The table below uses firmware listings posted on the Hovatek forum in May 2026. It shows how much the chipset, and therefore the tool, varies even inside one series.

Model Model code Chipset Firmware format
Infinix Note 50 Pro (4G) X6855 MediaTek Helio G100 Ultimate Scatter
Infinix Hot 60 Pro X6885 MediaTek Helio G200 Scatter
Infinix Hot 40 Pro X6837 MediaTek Helio G99 Scatter
Infinix Smart 8 Pro X6525B MediaTek Helio G36 Scatter
Infinix Smart 10 Plus X6725B / X6725C Unisoc T7250 .pac

How to Find Your Model Code and Build Number

Open Settings > About phone and note the model and the build number. Infinix build numbers start with the model code, for example X6855-16.2.0.135SP15_OP010PF001AZ on a Note 50 Pro. Write the full build number down before you flash. Hovatek advises this because knowing your current build makes it easy to go back to the most compatible firmware if a new one is buggy.

Requirements

  • A Windows PC and a good USB data cable.
  • The right driver: the MTK USB Driver for MediaTek phones, or the SPD SCI Android USB Driver for Unisoc phones.
  • Firmware made for your exact model code and variant. “Same series” is not enough: firmware for the Smart 10 Plus (X6725) is not for a Smart 8 Pro (X6525B), even though both are Smart models.
  • Battery charged to at least 50%.
  • A backup. A full flash usually erases everything on the phone. On a working phone, open Settings > Google > All services > Backup and tap Back up now (see Google’s backup help), and copy your photos to a PC.

We could not find a public firmware download page on Infinix’s own websites, so most stock ROM files come from community sites. Use only files labelled as factory or signed builds for your model, and stay with the same build family you already have when possible. Android Verified Boot includes rollback protection against older, vulnerable versions, so flashing an older build can fail.

How to Flash an Infinix MediaTek Phone with SP Flash Tool

  1. Install the MediaTek USB VCOM driver with the phone disconnected.
  2. Extract SP Flash Tool to a short folder path such as C:\SPFlashTool, and extract the firmware to a separate folder.
  3. Run flash_tool.exe as administrator.
  4. Load the firmware. In SP Flash Tool v5, click Choose next to the scatter-loading file and select the MTxxxx_Android_scatter.txt file. If your firmware has flash.xml instead, follow our SP Flash Tool v6 guide.
  5. Select Download Only. Do not choose Format All + Download.
  6. Click Download. Switch the phone off completely, then connect it to the PC. If nothing happens, unplug it and reconnect while holding Volume Up or Volume Down.
  7. Wait for the green success message (Download OK or a green tick). Do not touch the cable until it appears.
  8. Disconnect the phone and switch it on. The first boot can take several minutes.

Warning: Format All + Download can damage the NVRAM/NVDATA partitions that hold the phone’s radio settings, and the phone may lose its mobile network afterwards. On secure-boot MediaTek phones, formatting can also make the Download Agent stop working, so the tool then asks for an authentication file.

How to Flash an Infinix Unisoc Phone with Upgrade Download

  1. Install the Spreadtrum SCI USB driver.
  2. Open the tool folder and run UpgradeDownload.exe. Research Download works the same way; see our SPD Flash Tool (ResearchDownload) page.
  3. Click the Load Packet icon at the top left and select the .pac file. Wait until its name appears at the top of the window.
  4. Leave the tool’s settings at their defaults. If you ever choose only some partitions, FDL1 and FDL2 must stay selected.
  5. Click Start downloading. The status under the progress bar changes to Waiting….
  6. Switch the phone off and connect it while holding its boot key (usually Volume Down, on some models Volume Up or both). Some phones need the key held until flashing is well under way.
  7. Wait for Passed. Then click Stop downloading, disconnect the phone and switch it on.

Hovatek’s notes for the three Unisoc tools: Upgrade Download is good for a full flash, Research Download is best for flashing only a few partitions, and Factory Download is for phones that boot-loop after flashing with the other tools.

Troubleshooting

The tool asks for an authentication file

Many MediaTek Infinix phones use secure boot. Without a Download Agent (DA) and authentication file made for that model, SP Flash Tool shows errors such as STATUS_SEC_AUTH_FILE_NEEDED (0xC0030012), S_INVALID_DA_FILE or S_FT_DOWNLOAD_FAIL (2004). Infinix does not publish these files. Do not use “auth bypass” tools; take the phone to a Carlcare service centre instead. For DA error 2004 on older phones, see MTK S_BROM_DOWNLOAD_DA_FAIL (ERROR 2004) Solved.

The phone is not detected

  • Reinstall the driver with the phone unplugged, then restart the PC. Our Android USB driver for Windows 11 guide covers Code 28, Code 43 and signature errors.
  • Use a rear USB port on a desktop PC, not a hub, and try another cable.
  • Make sure the phone is fully off, then try a different volume key while connecting.

Upgrade Download stays on “Waiting…”

The tool cannot see the phone. Check the SCI driver, try another USB port, and hold Volume Down while you connect the cable.

The phone is stuck on the logo after flashing

Give the first boot at least 10 minutes. If it still does not start, check that the firmware matches your model code and flash again. A factory reset from recovery mode can also help, but it erases all data. Our boot loop guide covers these steps in order.

No mobile network after flashing

This usually means the NVRAM/NVDATA area was damaged, often by formatting or by firmware from another variant. Do not keep reflashing; take the phone to Carlcare.

Related Guides

FAQ

Does Infinix have its own official flash tool?

Not one that is available to the public. Infinix updates phones over the air, and Carlcare service centres handle software repairs. The tools people use at home are the chipset makers’ tools: SP Flash Tool for MediaTek and Upgrade Download or Research Download for Unisoc.

Will flashing Infinix firmware erase my data?

A full flash normally erases all user data, including photos, apps and accounts. Back up first. An OTA update from Settings normally keeps your data, but a backup is still wise.

Can I flash firmware from a similar Infinix model?

No. Use only firmware for your exact model code and variant. Firmware from another variant can leave the phone dead or without network.

Does flashing stock firmware unlock the bootloader or root the phone?

No. Official factory firmware keeps the phone in its normal locked state. It simply reinstalls the original software.

Can I use Odin or Mi Flash Tool on an Infinix phone?

No. Odin works only with Samsung phones, and Mi Flash Tool is made for Xiaomi phones. Infinix phones need the tool that matches their MediaTek or Unisoc chip.

https://droid-developers.com/wp-content/uploads/2026/11/infinix-firmware-flash-tool-featured-1024x538.jpghttps://droid-developers.com/wp-content/uploads/2026/11/infinix-firmware-flash-tool-featured-150x150.jpgFahim MahmudFirmwareFlash ToolsHow ToThere is no single Infinix firmware flash tool: the right tool depends on the chip inside your phone. Infinix phones with MediaTek chips are flashed with SP Flash Tool and a scatter file, while models with Unisoc chips use the Upgrade Download or Research Download tool with a .pac...Android Help,Troubleshooting  & Stock Rom